How to build

Rail LED holder

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

How to build the new rail led holder guide.
 
This is the new model of 3d printable rail led holder.
 
All parts from this guide can be used with the SuperGreenLab construction set.

What you'll need

Selected region:
World
Click to change

Rail LED holder BY SuperGreenTomato

From SuperGreenTomato EU

New rail LED holders!

It comes with 6 rail pieces (each 20cm | 7.8in) and 4 LED holders;
**perfect for small verti

US$41.75

*converted to local currency

SGL Construction Set BY SuperGreenLab

From SuperGreenLab

All the parts used for the SGL kits.

SuperGreenLab's construction set.
 
If you own a 3d printer these are all the parts used to cre

Holder wrist

Done
logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Holder wrist

Done

Push the transparent holder part into the arm's wrist.
 
Then add a 16mm screw to secure the holder in place.

Got a feedback/suggestion? click here

Attach arm

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Attach arm

Now attach the arm to the wrist, use a square nut on one side to screw everything together.

Got a feedback/suggestion? click here

Important notice

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Important notice

You will notice that the slider part has a bulge, which will be meant to be facing downward.
 
Which means we'll have to invert the slider part on two of the holders. It's explained further in the next steps.
 
Go through the whole page before starting from here.

Got a feedback/suggestion? click here

Bottom holders

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Bottom holders

So now we'll have to make 4 holders, two will be the lower ones, and two will be the top ones.
 
The lower holders will have the slider's bulge in the same direction is a semi-transparent part, as indicated on the picture.

Got a feedback/suggestion? click here

Top holders

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Top holders

And the top holders will have it facing the other direction.

Got a feedback/suggestion? click here

Attach slider

Done
logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Attach slider

Done

Ok so now that this part is clear, we're ready to make our four holders.
 
Don't forget, you want two top ones, and two lower ones, so basically just rotate the slider 180° for two of them.

Got a feedback/suggestion? click here

Rail setup

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Rail setup

Now all the holders are ready to be mounted to their rails!
 
You have six rails with the kit, you can join them together of have them in different places.
&nsbp;
Usual setup is to put three rails per sides, so the holders have enough height covered.

Got a feedback/suggestion? click here

Corner holders

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Corner holders

The rails can also be places in the corner, which is the most optimal place when dealing with small spaces like an Eket, or any narrow and vertical boxes.
 
The kit includes two corner holders per rails, you can attach them to the rails, you might need to glue them in place, but they should hold well already.
&nsbp;
To attach the corner holders to the rail, you need to slide them from the side of the rail.

Got a feedback/suggestion? click here

Done

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Done

Alright our rail holders are now done and ready to be glued to their furniture.
 
You can either place them in a corner or a flat surface.

Got a feedback/suggestion? click here

Glue in place

logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Glue in place

You can either use hot glue or strong double tape, don't worry the panels are quite light themselves.
 
In both cases, don't forget to slightly sand-paper the surface before glueing, some furnitures have a very slick surface, which is not the best for adhesiveness.

Got a feedback/suggestion? click here

Tightening screw

Done
logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Tightening screw

Done

Add the little screw to the side hole of the slider.
 
No need to tighten it, just enough to keep the slider in place.

Got a feedback/suggestion? click here

Tighten the screws

Done
logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

Tighten the screws

Done

Once the holder is glued to your furniture you can tighten the screws.
 
Don't over tighten is tho, just enough for it to stay in place.

Got a feedback/suggestion? click here

And you're done!

Done
logo-supergreenlab
Author: SuperGreenLab
Credit: SuperGreenLab

And you're done!

Done

Make sure there's some space between the top of the pot and the lower panels.

Got a feedback/suggestion? click here

Welcome to

Super Green Lab
SuperGreenLab is a community of stealth growers.
checkout our dedicated grow lights and smart controller and join the community!
Start growing

Subscribe

Stay tuned with our newsletter and get exclusive promotions.
Subscribe
© 2021 SuperGreenLab. All Rights Reserved